WesAudio CALYPSO

Main Features
Integration with I.A.C. (Internal Audio Connector) inside _TITAN chassis features almost wire-free setup

	Standard 500 chassis support CALYPSO is designed to work with standard 500 series enclosures, in that case DB-25 connectors on the front panel can be used to route audio signal to and from chassis. DB-25 connectors can be also used to route audio signal from and to outboard gear!
Convinient Plug-in for I.A.C. recall and more! _CALYPSO as all ng500 units is integrated with VST2/VST3/AAX/AU plug-ins. While using with a _TITAN it allows to manage I.A.C. connector in other words it manages input source to each module to be either back XLR “IN” socket, or I.A.C. direct connection to _CALYPSO. This gives You totally recallable solution to route your signal differently based on DAW session. For more information please refer to examples section below!  Plug-in features • Convinient metering • Full unit control • I.A.C. recall and management • Sample rate selection based on DAW session For more information please refer to manual
	LCD screen with metering Calypso LCD screen will allow You to see all configuration options and manage the unit. 1) Channel numbers 2) Metering – _CALYPSO supports very fast and accurate PPM metering 3) Clip indicator. 4) Currently active Sample Rate. 5) Source of Sample Rate configuration 6) Clock Source 7) Clock sync status 8) H-LINK – indication if DAW plug-in is connected to this particular hardware instance

WesAudio _CALYPSO used with _TITAN chassis features extremely convinient connectivity!

Features
• 24bit conversion
• Supported sample rates: 44.1kHz, 48kHz, 88.2kHz(SMUX), 96kHz(SMUX)
• Ultra low jitter clock
• Word clock IN/OUT
• Full integration with _TITAN via IAC connector (Just ADAT cables are need to route all signal to and from chassis)
• Two DB25 connectors allows integration with any 500 series chassis
• Two converter reference levels +8dBu/-10dBV
• LCD screen with channel metering

Specifications
• Power consumption: 150mA per rail
• Dimensions : 76x133x158mm

Inputs(ADC)
• Freq. response – 20Hz-20kHzm +/- 0.1dB
• THD+N (unweighted): -108dB (0.0004%)
• Dynamic range (unweighted): 116dB
• Gain Settings: +4 dBu / –10 dBV (selectable per input)
• Maximum Input Level: (+4 dBu) +20 dBu
• Input Impedance: 10K Ohms
• Connector type: DB25/IAC

Outputs(DAC)
• Freq. response – 20Hz-20kHzm +/- 0.1dB
• THD+N (unweighted): -105dB (0.0005%)
• Dynamic range (unweighted): 115dB
• Gain Settings: +4 dBu / –10 dBV (selectable per output)
• Maximum Output level: (+4 dBu) +20dBu
• Output Impedance: 100 Ohms
• Connector type: DB25/IAC

SETUP EXAMPLES
CALYPSO inside TITAN allow us to switch between different setus using convinient I.A.C. recall thorugh DAW plugin. As this functionality can be explored and integrated in many ways, below examples may give You a good idea how to start!

1) Recording and HW insert mixing mode setup
This setup is perfect for any studio which values easy switching between sessions. For instance, recording session is ongoing, but only for a part of a day, ability to get back to work on different mixing projects without any setup changes (RECALL!), is really convenient! For more details please refer to below picture

2) HW insert mode and units chaining
This particular setup allows to switch between two modes
• HW insert mode which allows to access each module separately
• And units chaining

Such mode can be useful, if for instance we would like to switch between mixing and mastering projects, or we simply would like to use modules in chain in some sessions

3) CALYPSO with external outboard gear
We can use I.A.C. connector to access modules independently. However there might be a situation that we would like to chain modules inside _TITAN with some outboard gear, and still use CALYPSO I/O. To configure such approach, there are two important things to be aware of:
• Modules in _TITAN chassis need to be last in chain (as “OUT” of each slot is hardwired with CALYPSO IN channel via I.A.C. connector).
• Signal has to be sent to outboard gear via DB-25 OUTPUT connector on _CALYPSO front panel